Choose your language

This is an optional feature for Rimaglio. With this kit, you can knit a 360° seam that secures the last course of the sock/tube leaving it open. This kit allows you to alternate 360° seam with regular toe-closing. It is particularly used in the production of knee pads and leg warmers.

A correct suction is necessary to run the machines.
These units must be equipped on the machine if your customer does not have a centralized vacuum unit.

This is the stand on which the yarn cones are placed.
There are two different types available: horizontal and vertical.

This device retrieves the yarn from the cone and delivers it to the knitting head with constant and adjustable tension, eliminating all the tension irregularities originated by the cones. Consequently, the sizes of the socks are more consistent, and it will be possible to knit yarns by having low resistance.
This device is recommended for machines with terry and needle count higher than 168.

We install LGL Ecopower 2 or BTSR Hyperfeeder.

This device retrieves the yarn from the cone and delivers it to the knitting head with a very precise, constant, and adjustable tension. In this way it eliminates all the tension irregularities originated by the cones. The feeding tension can be graduated during knitting by sending signals from an electronic board (Ultrafeeder preparation) through a serial line.

This device is indispensable for feeding bare Lycra.

It enables to retrieve the yarn during the heel.
It only works with BTSR Ultrafeeder 2 and replaces the heel take-up.

Through this special device, it is possible to knit socks with 3 dimensional effects as in the picture below.

It enables the machine to knit footie socks.

This option enables the machine to drive two or more heel take-ups independently. 

This device is useful when producing long pantyhose.
The machine will deliver the socks with no twist and without wrinkles.

Same as the above, but this version can fit on machines equipped with Rimaglio, our toe-closing device.

It is the clamp to hold the bare Lycra. It cannot be used in case the machine knits terry. 1 or 2 clamps are available according to the model.

The machine is equipped with a device that enables it to produce mesh patterns (also called filet stitch) in two feeds.
The standard machine produces such mesh patterns in one feed only.
This option is commonly used for the pantyhose, to shorten the production time.

With this device you can create patterns which also cover the whole heel and toe areas of the sock.
The compatibility of this option shall be considered case by case.

This device can be installed on the machines with Rimaglio device and enables them to eject the sock inside-out. This is normally requested for an easier inspection of the socks. 

With this special device it is possible to knit terry approximately 30% shorter than the standard.

With this kit your machine will have one additional yarn finger for the elastic on the first feed.

This device stops the machine when the yarn is stuck, preventing it from tearing up.
It is built so as not to make the machine re-thread after the stop.

This device consists in several sensors that electronically detect when the yarn is flowing and when it is steady. During the production of the first sock, the information about the yarn flow is stored into a memory on an electronic board (BTSR preparation). During the production of all the following socks, the device checks that the yarns flow with the same sequence as the first one. In case of any errors, the machine stops avoiding the production of second choice socks.
The machine is equipped with 18 sensors as standard, you can request it with 6 or 24 sensors.

This device can be installed only on machines which cannot knit terry, and it enables knitting socks with a reinforcing yarn in the sole/high heel areas.
The reinforcing yarn will be plated to the inside of the sock. It will also be possible to add a pattern on the reinforced area.

This device is necessary for feeding the elastic yarns without putting any radial pressure on the elastic yarn itself. They are normally used in the MEDICAL and MEDICAL TERRY machines.
It can be associated with BTSR Ultrafeeder.

The 2-feed machine guarantees higher productivity (approx. +20%) than the 1-feed machine (in case of socks without patterns).

This kit enables the machine to knit mittens. Available on BUSI® 500.

This kit gives the possibility to knit a vertical hole on the sock.

With this kit you get the board to connect the storage feeder (Brand Memminger and LGL)

This kit enables the MEDICAL TERRY machine to knit the selected terry.

With this sinker cap you will be able to do plated and non-plated terry on your sock.

With this kit you will have the 6th color on your machine. It is available for IDEA, IDEA TERRY and J TERRY.